iOS Development environment Xcode 16.4, macOS 15.6.1 (24G90) Run-time configuration: iOS 17.2+ Short Description After having successfully established an NWConnection (either as UDP or TCP), and subsequently receiving the error code: UDP Connection failed: 57 The operation couldn't be completed. (Network.NWError error 57 - Socket is not connected), available Interfaces: [enO] via NWConnection.stateUpdateHandler = { (newState) in ... } while newState == .failed the data connection does not restart by itself once cellular (RF) telephony coverage is established again. Detailed Description Context: my app has a continuous cellular data connection while in use. Either a UDP or a TCP connection is established depending on the user settings. The setup data connection works fine until the data connection gets disconnected by loss of connection to a available cellular phone base station. This disconnection simply occurs in very poor UMTS or GSM cellular phone coverage. This is totally normal behavior in bad reception areas like in mountains with signal loss. STEPS TO REPRODUCE Pre-condition App is running with active data connection. Action iPhone does loss the cellular data connection previously setup. Typically reported as network error code 57. Observed The programmed connection.stateUpdateHandler() is called in network connection state '.failed' (OK). The self-programmed data re-connection includes: a call to self.connection.cancel() a call to self.setupUDPConnection() or self.setupConnection() depending on the user settings to re-establish an operative data connection. However, the iPhone's UMTS/GSM network data (re-)connection state is not properly identified/notified via NWConnection API. There's no further network state notification by means of NWConnection even though the iPhone has recovered a cellular data network. Expected The iPhone or any other means automatically reconnects the interrupted data connection on its own. The connection.stateUpdateHandler() is called at time of the device's networking data connection (RF) recovering, subsequently to a connection state failed with error code 57, as the RF module is continuously (independently from the app) for available telephony networks. QUESTION How to systematically/properly detect a cellular phone data network reconnection readiness in order to causally reinitialize the NWConnection data connection available used in app. Relevant code extract Setup UDP connection (or similarly setup a TCP connection) func setupUDPConnection() { let udp = NWProtocolUDP.Options.init() udp.preferNoChecksum = false let params = NWParameters.init(dtls: nil, udp: udp) params.serviceClass = .responsiveData // service type for medium-delay tolerant, elastic and inelastic flow, bursty, and long-lived connections connection = NWConnection(host: NWEndpoint.Host.name(AppConstant.Web.urlWebSafeSky, nil), port: NWEndpoint.Port(rawValue: AppConstant.Web.urlWebSafeSkyPort)!, using: params) connection.stateUpdateHandler = { (newState) in switch (newState) { case .ready: //print("UDP Socket State: Ready") self.receiveUDPConnection(). // data reception works fine until network loss break case .setup: //print("UDP Socket State: Setup") break case .cancelled: //print("UDP Socket State: Cancelled") break case .preparing: //print("UDP Socket State: Preparing") break case .waiting(let error): Logger.logMessage(message: "UDP Connection waiting: "+error.errorCode.description+" \(error.localizedDescription), available Interfaces: \(self.connection.currentPath!.availableInterfaces.description)", LoggerLevels.Error) break case .failed(let error): Logger.logMessage(message: "UDP Connection failed: "+error.errorCode.description+" \(error.localizedDescription), available Interfaces: \(self.connection.currentPath!.availableInterfaces.description)", LoggerLevels.Error) // data connection retry (expecting network transport layer to be available) self.reConnectionServer() break default: //print("UDP Socket State: Waiting or Failed") break } self.handleStateChange() } connection.start(queue: queue) } Handling of network data connection loss private func reConnectionServer() { self.connection.cancel() // Re Init Connection - Give a little time to network recovery let delayInSec = 30.0. // expecting actually a notification for network data connection availability, instead of a time-triggered retry self.queue.asyncAfter(deadline: .now() + delayInSec) { switch NetworkConnectionType { case 1: self.setupUDPConnection() // UDP break case 2: self.setupConnection() // TCP break default: break } } } Does it necessarily require the use of CoreTelephony class CTTelephonyNetworkInfo or class CTCellularData to get notifications of changes to the user’s cellular service provider?

I cannot find in the documentation and samples how exactly the Bloom filter is generated. Is there any code sample for that?

Hi, We’re seeing our build system (Gradle) get stuck in sendto system calls while trying to communicate with other processes via the local interface over UDP. To the end user it appears that the build is stuck or they will receive an error “Timeout waiting to lock XXX. It is currently in use by another Gradle instance”. But when the process is sampled/profiled, we can see one of the threads is stuck in a sendto system call. The only way to resolve the issue is to kill -s KILL <pid> the stuck Gradle process. A part of the JVM level stack trace: "jar transforms Thread 12" #90 prio=5 os_prio=31 cpu=0.85ms elapsed=1257.67s tid=0x000000012e6cd400 nid=0x10f03 runnable [0x0000000332f0d000] java.lang.Thread.State: RUNNABLE at sun.nio.ch.DatagramChannelImpl.send0(java.base@17.0.10/Native Method) at sun.nio.ch.DatagramChannelImpl.sendFromNativeBuffer(java.base@17.0.10/DatagramChannelImpl.java:901) at sun.nio.ch.DatagramChannelImpl.send(java.base@17.0.10/DatagramChannelImpl.java:863) at sun.nio.ch.DatagramChannelImpl.send(java.base@17.0.10/DatagramChannelImpl.java:821) at sun.nio.ch.DatagramChannelImpl.blockingSend(java.base@17.0.10/DatagramChannelImpl.java:853) at sun.nio.ch.DatagramSocketAdaptor.send(java.base@17.0.10/DatagramSocketAdaptor.java:218) at java.net.DatagramSocket.send(java.base@17.0.10/DatagramSocket.java:664) at org.gradle.cache.internal.locklistener.FileLockCommunicator.pingOwner(FileLockCommunicator.java:61) at org.gradle.cache.internal.locklistener.DefaultFileLockContentionHandler.maybePingOwner(DefaultFileLockContentionHandler.java:203) at org.gradle.cache.internal.DefaultFileLockManager$DefaultFileLock$1.run(DefaultFileLockManager.java:380) at org.gradle.internal.io.ExponentialBackoff.retryUntil(ExponentialBackoff.java:72) at org.gradle.cache.internal.DefaultFileLockManager$DefaultFileLock.lockStateRegion(DefaultFileLockManager.java:362) at org.gradle.cache.internal.DefaultFileLockManager$DefaultFileLock.lock(DefaultFileLockManager.java:293) at org.gradle.cache.internal.DefaultFileLockManager$DefaultFileLock.<init>(DefaultFileLockManager.java:164) at org.gradle.cache.internal.DefaultFileLockManager.lock(DefaultFileLockManager.java:110) at org.gradle.cache.internal.LockOnDemandCrossProcessCacheAccess.incrementLockCount(LockOnDemandCrossProcessCacheAccess.java:106) at org.gradle.cache.internal.LockOnDemandCrossProcessCacheAccess.acquireFileLock(LockOnDemandCrossProcessCacheAccess.java:168) at org.gradle.cache.internal.CrossProcessSynchronizingCache.put(CrossProcessSynchronizingCache.java:57) at org.gradle.api.internal.changedetection.state.DefaultFileAccessTimeJournal.setLastAccessTime(DefaultFileAccessTimeJournal.java:85) at org.gradle.internal.file.impl.SingleDepthFileAccessTracker.markAccessed(SingleDepthFileAccessTracker.java:51) at org.gradle.internal.classpath.DefaultCachedClasspathTransformer.markAccessed(DefaultCachedClasspathTransformer.java:209) at org.gradle.internal.classpath.DefaultCachedClasspathTransformer.transformFile(DefaultCachedClasspathTransformer.java:194) at org.gradle.internal.classpath.DefaultCachedClasspathTransformer.lambda$cachedFile$6(DefaultCachedClasspathTransformer.java:186) at org.gradle.internal.classpath.DefaultCachedClasspathTransformer$$Lambda$368/0x0000007001393a78.call(Unknown Source) at org.gradle.internal.UncheckedException.unchecked(UncheckedException.java:74) at org.gradle.internal.classpath.DefaultCachedClasspathTransformer.lambda$transformAll$8(DefaultCachedClasspathTransformer.java:233) at org.gradle.internal.classpath.DefaultCachedClasspathTransformer$$Lambda$372/0x0000007001398470.call(Unknown Source) at java.util.concurrent.FutureTask.run(java.base@17.0.10/FutureTask.java:264) at org.gradle.internal.concurrent.ExecutorPolicy$CatchAndRecordFailures.onExecute(ExecutorPolicy.java:64) at org.gradle.internal.concurrent.ManagedExecutorImpl$1.run(ManagedExecutorImpl.java:49) at java.util.concurrent.ThreadPoolExecutor.runWorker(java.base@17.0.10/ThreadPoolExecutor.java:1136) at java.util.concurrent.ThreadPoolExecutor$Worker.run(java.base@17.0.10/ThreadPoolExecutor.java:635) at java.lang.Thread.run(java.base@17.0.10/Thread.java:840) A part of the process sample: 2097 Thread_3879661: Java: jar transforms Thread 12 + 2097 thread_start (in libsystem_pthread.dylib) + 8 [0x18c42eb80] ...removed for brevity... + 2097 Java_sun_nio_ch_DatagramChannelImpl_send0 (in libnio.dylib) + 84 [0x102ef371c] + 2097 __sendto (in libsystem_kernel.dylib) + 8 [0x18c3f612c] We have observed the following system logs around the time the issue manifests: 2025-08-26 22:03:23.280255+0100 0x3b2c00 Default 0x0 0 0 kernel: cfil_hash_entry_log:6088 <CFIL: Error: sosend_reinject() failed>: [4628 java] <UDP(17) in so 9e934ceda1c13379 50826943645358435 50826943645358435 ag> 2025-08-26 22:03:23.280267+0100 0x3b2c00 Default 0x0 0 0 kernel: cfil_service_inject_queue:4472 CFIL: sosend() failed 22 The issue seems to be rooted in the built-in Application Firewall, as disabling it “fixes” the issue. It doesn’t seem to matter that the process is on the “allow” list. We’re using Gradle 7.6.4, 8.0.2 and 8.14.1 in various repositories, so the version doesn’t seem to matter, neither does which repo we use. The most reliable way to reproduce is to run two Gradle builds at the same time or very quickly after each other. We would really appreciate a fix for this as it really negatively affects the developer experience. I've raised FB19916240 for this. Many thanks,

This is a major issue. After my iPhone 12 Pro was upgraded to iOS 26 beta 6, Apple's official Wi-Fi Aware Sample APP crashed immediately and couldn't be opened. It just force closes. Has any developer encountered this problem?

When I try to implement the new Background Task options in the same way as they show in the WWDC video (on watchOS) likes this: let config = URLSessionConfiguration.background(withIdentifier: "SESSION_ID") config.sessionSendsLaunchEvents = true let session = URLSession(configuration: config) let response = await withTaskCancellationHandler {       try? await session.data(for: request) } onCancel: {       let task = session.downloadTask(with: request))       task.resume() } I'm receiving the following error: Terminating app due to uncaught exception 'NSGenericException', reason: 'Completion handler blocks are not supported in background sessions. Use a delegate instead.' Did I forget something?

iPhone 12 pro with iOS 26.0 (23A5276f) App: https://developer.apple.com/documentation/wifiaware/building-peer-to-peer-apps We aim to use Wi-Fi Aware to establish file transfer between Android and Apple devices. Apple will act as the Publisher, and Android will act as the Subscriber. According to the pairing process outlined in the Wi-Fi Aware protocol (Figure 49 in the Wi-Fi Aware 4.0 specification), the three PASN Authentication frames have been successfully exchanged. Subsequently, Android sends the encrypted Follow-up PMF to Apple, but the Apple log shows: Failed to parse event. Please refer to the attached complete log. We request Apple to provide a solution. apple Log-20250808a.txt

Hi everyone, I’ve been working with the NEPacketTunnelProvider class and came across the cancelTunnelWithError() method. The documentation mentions its general purpose but doesn’t provide much clarity on how and when it should be called. From what I’ve gathered in other forum posts, it seems that cancelTunnelWithError() should be called within my own implementation of the stopTunnel() method, but I’m not entirely sure if that’s the correct usage or whether there are specific scenarios where this applies. Here are my specific questions: Is it correct to always call cancelTunnelWithError() in my implementation of stopTunnel()? Are there specific conditions or scenarios where cancelTunnelWithError() is the preferred way to terminate a tunnel session, rather than other termination methods? What does the system do with the error that I pass to cancelTunnelWithError()? Does it have an impact on how the session termination is handled? Are there best practices or common pitfalls to avoid when using cancelTunnelWithError()? Any insights, examples, or guidance would be greatly appreciated! Thanks in advance for your help!

how can I prevent handshake when certificate is user installed for example if user is using Proxyman or Charles proxy and they install their own certificates now system is trusting those certificates I wanna prevent that, and exclude those certificates that are installed by user, and accept the handshake if CA certificate is in a real valid certificate defined in OS I know this can be done in android by setting something like <network-security-config> <base-config> <trust-anchors> <certificates src="system" /> </trust-anchors> </base-config> </network-security-config>

For a past few days, I have been exploring control Filter and data filter. I am unable to understand how control moves from various functions of data filter to control Filter. One thing that I am unable to figure out is that when I pass verdict as .allow in dataFilter's handleNewFlow and mark .shouldReport as true, I get inBytes and outbytes in the flow report of handle() in controlFilter. But when I pass verdict as needRules and wait till the handle is called in controlFilter when the report.event == .flowClosed, I don't get inBytes and outBytes. I am unable to understand this complete flow of network extension from the apple documentation. Can someone provide me with some flow chart or some pictorial representation or detailed explanation of network extension for iOS? Also is there some way to imitate the ..statisticsReportFrequency for iOS as it is not available for iOS?

I haven’t been able to get this to work at any level! I’m running into multiple issues, any light shed on any of these would be nice: I can’t implement a bloom filter that produces the same output as can be found in the SimpleURLFilter sample project, after following the textual description of it that’s available in the documentation. No clue what my implementation is doing wrong, and because of the nature of hashing, there is no way to know. Specifically: The web is full of implementations of FNV-1a and MurmurHash3, and they all produce different hashes for the same input. Can we get the proper hashes for some sample strings, so we know which is the “correct” one? Similarly, different implementations use different encodings for the strings to hash. Which should we use here? The formulas for numberOfBits and numberOfHashes give Doubles and assign them to Ints. It seems we should do this conversing by rounding them, is this correct? Can we get a sample correct value for the combined hash, so we can verify our implementations against it? Or ignoring all of the above, can we have the actual code instead of a textual description of it? 😓 I managed to get Settings to register my first attempt at this extension in beta 1. Now, in beta 2, any other project (including the sample code) will redirect to Settings, show the Allow/Deny message box, I tap Allow, and then nothing happens. This must be a bug, right? Whenever I try to enable the only extension that Settings accepted (by setting its isEnabled to true), its status goes to .stopped and the error is, of course, .unknown. How do I debug this? While the extension is .stopped, ALL URL LOADS are blocked on the device. Is this to be expected? (shouldFailClosed is set to false) Is there any way to manually reload the bloom filter? My app ships blocklist updates with background push, so it would be wasteful to fetch the filter at a fixed interval. If so, can we opt out of the periodic fetch altogether? I initially believed the API to be near useless because I didn’t know of its “fuzzy matching” capabilities, which I’ve discovered by accident in a forum post. It’d be nice if those were documented somewhere! Thanks!!

If the includeAllNetworks flag to true, we cannot update our app via Xcode, TestFlight or the AppStore. In the AppStore and TestFlight cases, it seems that the packet tunnel process is stopped before the new app is downloaded - once the packet tunnel process is stopped, it can’t be started again via Settings/VPN profiles, nor can it be started via the app.

Hey everyone, I’m developing an app for visionOS where I need to display the Apple Vision Pro’s current IP address. For this I’m using the following code, which works for iOS, macOS, and visionOS in the simulator. Only on a real Apple Vision Pro it’s unable to extract an IP. Could it be that visionOS currently doesn’t allow this? Have any of you had the same experience and found a workaround? var address: String = "no ip" var ifaddr: UnsafeMutablePointer<ifaddrs>? = nil if getifaddrs(&ifaddr) == 0 { var ptr = ifaddr while ptr != nil { defer { ptr = ptr?.pointee.ifa_next } let interface = ptr?.pointee let addrFamily = interface?.ifa_addr.pointee.sa_family if addrFamily == UInt8(AF_INET) { if let name: Optional<String> = String(cString: (interface?.ifa_name)!), name == "en0" { var hostname = [CChar](repeating: 0, count: Int(NI_MAXHOST)) getnameinfo(interface?.ifa_addr, socklen_t((interface?.ifa_addr.pointee.sa_len)!), &hostname, socklen_t(hostname.count), nil, socklen_t(0), NI_NUMERICHOST) address = String(cString: hostname) } } } freeifaddrs(ifaddr) } return address } Thanks in advance for any insights or tips! Best Regards, David

Simulator: iPhone 16 pro (iOS 26) Minimum Deployments: iOS 16.0+, not iOS 17. Here is the demo: import SwiftUI import NetworkExtension struct ContentView: View { private var monitor = NWPathMonitor() var body: some View { VStack { Text("Hello, world!") } .task { let _ = URLSession.shared } } }

Hello! I develop transparent proxy based application, and I'm receiving a lot of crash reports from macOS 15.5 for crash in __88-[NEExtensionAppProxyProviderContext setInitialFlowDivertControlSocket:extraValidation:]_block_invoke.90 when stopping. Even very old versions of my software started crashing on macOS 15.5. I checked my extension that it correctly calls setTunnelNetworkSettings:nil on proxy stop, but crash is still here. Does anybody else have this problem? Do you know any workaround for it?

Hello, I am writing a NetworkExtension VPN using custom protocol and our client would like to able to use 5G network slice on the VPN, is this possible at all? From Apple's documentation, I found the following statement: If both network slicing and VPN are configured for an app or device, the VPN connection takes precedence over the network slice, rendering the network slice unused. Is it possible to assign a network slice on a NetworkExtension-based VPN and let the VPN traffic uses the assign network slice? Many thanks

Hi all, We've been exploring the capabilities of the Network.framework for peer-to-peer communication and have run into some behavior that we haven't been able to fully explain with the existing documentation. In our tests, we’re working with 12 iOS devices, all disconnected from Wi-Fi to force communication over Apple Wireless Direct Link (AWDL). While using the Network.framework to create peer-to-peer connections, we observed that the number of connected peers never exceeded 8, despite all 12 devices being active and configured identically. Some questions we’re hoping to get clarification or discussion on: Is there a known upper limit to the number of peer-to-peer connections supported via AWDL? Are there conditions under which the framework or system limits or throttles visible peers? Does AWDL behavior vary by hardware model, iOS version, or backgrounding state of the app? Is there any official documentation or guidance around peer discovery or connection limits when using NWBrowser and NWConnection in a peer-to-peer context? We’d appreciate any insights from the Apple engineering team or other developers who have worked with larger peer groups using Network.framework in peer-to-peer mode.

Goal : Block all outbound connections to a static list of hosts (both In-app requests and WKWebView/Safari). App & both extensions have Network Extension entitlement with content-filter-provider and filter-control-provider What’s working: Safari and WKWebView requests matching the block list are dropped. What’s broken: In-app traffic never reaches the Data Provider—those requests always succeed. Setup: • NEFilterProviderConfiguration with both Data & Control providers, filterBrowsers = true, filterSockets = true • Data Provider implements handleNewFlow for socket/browser flows • Control Provider implements handleNewFlow for browser flows • Enabled via saveToPreferences() and toggled ON in Settings

Hi, I've encountered a strange behavior in the DNS Proxy Provider extension. Our app implements both DNS Proxy Provider and Content Filter Providers extensions, configured via MDM. When the app is uninstalled, the behavior of the providers differs: For Content Filter Providers (both Filter Control and Filter Data Providers), the providers stop as expected with the stop reason: /** @const NEProviderStopReasonProviderDisabled The provider was disabled. */ case providerDisabled = 5 However, for the DNS Proxy Provider, the provider remains in the "Running" state, even though there is no app available to match the provider's bundle ID in the uploaded configuration profile. When the app is reinstalled: The Content Filter Providers start as expected. The DNS Proxy Provider stops with the stop reason: /** @const NEProviderStopReasonAppUpdate The NEProvider is being updated */ @available(iOS 13.0, *) case appUpdate = 16 At this point, the DNS Proxy Provider remains in an 'Invalid' state. Reinstalling the app a second time seems to resolve the issue, with both the DNS Proxy Provider and Content Filter Providers starting as expected. This issue seems to occur only if some time has passed after the DNS Proxy Provider entered the 'Running' state. It appears as though the system retains a stale configuration for the DNS Proxy Provider, even after the app has been removed. Steps to reproduce: Install the app and configure both DNS Proxy Provider and Content Filter Providers using MDM. Uninstall the app. Content Filter Providers are stopped as expected (NEProviderStopReason.providerDisabled = 5). DNS Proxy Provider remains in the 'Running' state. Reinstall the app. Content Filter Providers start as expected. DNS Proxy Provider stops with NEProviderStopReason.appUpdate (16) and remains 'Invalid'. Reinstall the app again. DNS Proxy Provider now starts as expected. This behavior raises concerns about how the system manages the lifecycle of DNS Proxy Provider, because DNS Proxy Provider is matched with provider bundle id in .mobileconfig file. Has anyone else experienced this issue? Any suggestions on how to address or debug this behavior would be highly appreciated. Thank you!

There are multiple report of crashes on URLConnectionLoader::loadWithWhatToDo. The crashed thread in the stack traces pointing to calls inside CFNetwork which seems to be internal library in iOS. The crash has happened quite a while already (but we cannot detect when the crash started to occur) and impacted multiple iOS versions recorded from iOS 15.4 to 18.4.1 that was recorded in Xcode crash report organizer so far. Unfortunately, we have no idea on how to reproduce it yet but the crash keeps on increasing and affect more on iOS 18 users (which makes sense because many people updated their iOS to the newer version) and we haven’t found any clue on what actually happened and how to fix it on the crash reports. What we understand is it seems to come from a network request that happened to trigger the crash but we need more information on what (condition) actually cause it and how to solve it. Hereby, I attach sample crash report for both iOS 15 and 18. I also have submitted a report (that include more crash reports) with number: FB17775979. Will appreciate any insight regarding this issue and any resolution that we can do to avoid it. iOS 15.crash iOS 18.crash

My app has local network permission on macOS Sequoia and works in most cases. I've noticed that after unlocking my MacBook Pro, the very first request will regularly fail with a No Route to Host. A simple retry resolves the issue, but I would have expected the very first request to succeed. Is this is a known issue on macOS Sequoia or by design? I'd prefer not to add a retry for this particular request as the app is a network utility.